PCTech Forums

Just reinforcing liljim, if you install XP after 95/98/2k the NT bootloader will automatically create boot options for both OSes. I used to dual boot 98 and 2k before I moved to Linux and this is how I set it up.

Perfect...

Win98SE is on IDE1 as Master
There is no slave

the CDRW is on IDE2 as master
the DVD as Slave

This should easy.....

I'm off to pick-up the HDD now ,that and a new CD-Rom for my server box.

I'll be back.

Cactus

Ok...the 52x cdrom in the other pc went flawless.

Now the HDD in this box is listed in the Device Manager...no exlamation marks.
But it doesn't show up in Windows Explorer.

I went into bios and everything is set to AUTO.
It is also listed correctly as the Slave on IDE1 on the boot-up screen.

What do I need to do here?
How do I f-disk and Format this drive with XP going on it?

Cactus

Can I use a Win98SE boot disk to get to FDISK and Format?

The drive isnt showing up because theres no partitions on it and yes you can use the 98 boot disk to partition and format it.However it may be easier to boot from the XP disk and let it partition and format the drive.I assume you will want to put XP in FAT32,win98 wont see the new drive if you use NTFS.If you use the XP disk,just be careful that you partiton and format the correct drive

ok...so shut it down and boot with cd in drive?

Ok... put in the cd and booted to WHAT DO YOU WANT TO DO?

Install XP
Perform Additional Task
Chk sys

I don't want to install over top the Win98SE HDD....

What do I do?

Is this what I do....

Unplug the HDD on IDE1Master.....

Take the NEW HDD,plug into IDE1 as master,F-Disk and Format with floppy,then install XP from CD.

When installation done,shut down pc,put back original hdd as master on IDE1 and the NEW drive with XP on same IDe1 as slave....


Is this correct...

I want to get my pc back together tonight.

Cactus

It sounds like you went back to win98 instead of booting from the disk.The XP disk should be "bootable".Set your cdrom as first boot device in bios and reboot with the cd again.

Just wanted to add that swapping the drives would allow you to install XP but i dont think it will set up the boot loader if both drives aren't present during the install.

ok I'm lost...
You want me to leave the original HDD as Master,put the newHDD as slave,Boot the pc with the cd rom,which i did and it booted to the screen i posted above.

If I click install it doesn't give me achoice of which hard drive to partition ...

So right now I have the orig HDD out...
the new in as primary
partition and formated with win98se floppy!!

Now I goto install winxp and it says CANT DO IN DOS??????

Ok,so now what?
Shut it down,put the orig HDD back as master on primary IDE,put the new formated HDD in as slave on primary and reboot with XPCD ?

Cactus

I set it back and an error came up no emultion????
Then immediatly booted to win 98se.
sob...now some of the removable drives have disappeared to...it doesn't show up n win explorere but it does show up in device manager


NOTE:I just rebooted without the cd in and now the second HDD does show....not accessable though.
3 of the card readers drives are missing as well....
what do I do now?

Cactus

ok...both drives show up...i formated from the cd.
now i'm at the set-up stage for xp...
I went in to ADVANCED and choose to pick the drive letter and partition...I'm at that screen right now.



I'm at the next screen...GET UPDATED SETUP FILES...what do i choose?

i'm pulling the drive....